LIGTRIX 48

 

LigTrix 48 Touring

LigTrix 48 Touring

LigTrix 48 Install

LigTrix 48 Install

The LigTrix 48 with inputs and outputs switchable in channel pairs between analogue or AES/EBU the LigTrix 48 gives you the flexibility you need to integrate into your system.

Compressors are available on every input as well as a high pass filter, 6 bands of parametric EQ, a 28 band graphic EQ, 3 bands of dynamic EQ and up to 1.3 seconds of delay. Routing to outputs can be configured to either mix-matrix mode, free-routing or several pre-configured routing options. Flexible channel linking enables quick and easy configuration of common crossover setups or customised configurations as required. Every output channel has high and low pass filters, 10 bands of parametric EQ and up to 1.3 seconds of delay. Also new is our Predictive eXcursion Limiter (PXL) algorithm designed to offer the best driver protection with the lowest distortion.

Front panel control allows instant mute of any input or output as well as editing of all the most commonly used parameters and recall of presets.

Our D-Net Ethernet based control software for PC, Mac and iPad gives you the ability to not only control all the devices on a network but also to store preset memories and configure systems offline.

Description: Remote control software for iPad, control the Ligwa LigTrix 48 Touring and LigTrix 48 Install processors and Quad-DSP amplifiers.
  • 20170427_212358047_iOS
  • 20170427_212520873_iOS 1
  • 20170427_212521037_iOS
  • iPad Screen Shot

    iPad Screen Shot

  • Processing [96kHz]

    Input Gain (per channel) : -30 to +15dB in 0.1dB steps, mute, phase
    Input Delay (per channel) : 0 to 1.3s in 10.4uS steps
    Input Compressor (per channel) : Threshold (-30 to +22 dBu), Attack, Release, Ratio, Soft-Knee
    Input Parametric EQ (per channel) : 6 bands – parametric, low shelf, high shelf, notch, band-pass
    Input Graphic EQ (per channel) : 28 bands
    Input Dynamic EQ (per channel) : 3 bands – parametric/low shelf/high shelf, boost/cut above/below, threshold, ratio, attack, release
    Input High-Pass Filter (per channel) : Up to 24dB/octave (Bensen / Butterworth / Bessel / Linkwitz-Riley)

    Routing Inputs to Outputs : Choice of modes (Matrix Mixer, Free Routing, 1×8 crossover, 2×4 crossover, 4×2 crossover, 2×3 crossover + 2 Aux)

    Output Parametric EQ (per channel) : 10 bands – parametric, low shelf, high shelf, notch, band-pass
    Output High-Pass and Low-Pass Filter (per channel) : Up to 48dB/octave (Bensen / Butterworth / Bessel / Linkwitz-Riley)
    Output Gain (per channel) : -30 to +15dB in 0.1dB steps, mute, phase
    Output Delay (per channel) : 0 to 1.3s in 10.4uS steps
    Output Limiter (per channel) : Threshold (-50 to +22dBu), attack, release, auto attack/release option

    Presets : Up to 30

    Comms

    100Mbps Ethernet on rear panel (Ethercon connector)
    USB Type B socket

  • Height : 44mm (1.75inch) 1U
    Depth : 213mm (8.4 inches)
    Width : 482mm (19 inches)

  • Net : 2.8kg

  • Frequency Response (20Hz to 20kHz) : +/-0.4dB
    Dynamic Range : >115dB unweighted (in to out analogue)
    THD + N (+10dB @ 1kHz) : 0.0013%
    Latency : 1.074ms (in to out, analogue)

     
     
  • Analogue Inputs – 4

    Electronically balanced, pin 2 hot
    CMRR : >60dB @ 1kHz
    Maximum Level : >20dBu
    Input Impedance : 10kΩ balanced

    AES Inputs – 2 x 2 channel

    Transformer balanced, pin 2 hot
    AES Input Sample Rates : 8kHz to 96kHz
    AES Input s/n Ratio : 139dB
    Input Impedance : 110Ω

    Analogue Outputs – 8

    Electronically balanced, pin 2 hot
    Maximum Level : >20dBu
    Source Impedance : <60Ω

    AES Outputs – 4 x 2 channel

    Transformer balanced, pin 2 hot
    Sample Rate : same as operating sample rate
    Source Impedance : 110Ω

  • 3-pin IEC input, fused
    90-250VAC, 50-60Hz < 40W